tutorials:arduino:controlling_led
Differences
This shows you the differences between two versions of the page.
|
tutorials:arduino:controlling_led [2014/02/25 16:37] sam [Headline] |
tutorials:arduino:controlling_led [2014/03/03 10:13] (current) allen [Source Code] |
||
|---|---|---|---|
| Line 3: | Line 3: | ||
| <WRAP noprint><WRAP left box 60%> | <WRAP noprint><WRAP left box 60%> | ||
| //__About this Article__// | //__About this Article__// | ||
| - | * **Author**: xxx --- xxx@cubietech.com --- 2014/02/25 14:41 | + | * **Author**: sam --- sam@cubietech.com --- 2014/02/25 14:41 |
| * **Copyrights**: [[http://creativecommons.org/licenses/by-sa/3.0/|CC Attribution-Share Alike 3.0 Unported]] | * **Copyrights**: [[http://creativecommons.org/licenses/by-sa/3.0/|CC Attribution-Share Alike 3.0 Unported]] | ||
| * **Contributors**: [[http://cubieboard.org/|Cubieboard Community]] : ... | * **Contributors**: [[http://cubieboard.org/|Cubieboard Community]] : ... | ||
| </WRAP></WRAP> | </WRAP></WRAP> | ||
| - | ===== Abstract ===== | + | ===== Make LED Lights flashing ===== |
| + | {{:tutorials:arduino:image.jpeg|400}} | ||
| + | ===== Schematics ===== | ||
| + | {{:tutorials:arduino:xlzomm.jpg?500|}} | ||
| + | ===== Steps ===== | ||
| - | ===== Headline ===== | + | 1. you should install arduino ide. Please refer to |
| + | [[http://docs.cubieboard.org/tutorials/arduino/connecting|how to connect cubieboard and arduino]] | ||
| + | 2. connect arduino and led as the Schematics | ||
| - | 1 connect arduino and led. | + | 3. Use usb to connect arduino and cubieboard . |
| + | |||
| + | 4. then we can start writing programs in arduino ide. | ||
| + | we still make LED lights flashing, lit one second turns off one second | ||
| + | =====Source Code===== | ||
| + | |||
| + | int ledPin = 10; //Defining Digital Interface 10 | ||
| + | void setup() | ||
| + | { | ||
| + | pinMode(ledPin, OUTPUT); //Definition of small lights interface output interface | ||
| + | } | ||
| + | void loop() | ||
| + | { | ||
| + | digitalWrite(ledPin, HIGH); //Lit lamp | ||
| + | delay(1000); //Delay 1 second | ||
| + | digitalWrite(ledPin, LOW); //Extinguish lamp | ||
| + | delay(1000); //Delay 1 second | ||
| + | } | ||
| + | | ||
| - | {{:tutorials:arduino:xlzomm.jpg?300|}} | ||
| - | 2 Use usb to connect arduino and cubieboard . | ||
| - | 3 then we can start writing programs in arduino ide. | ||
| - | we still make LED lights flashing, lit one second turns off one second | ||
| - | {{:tutorials:arduino:img_20140225_160749.jpg?300|}} | ||
| - | ==== Headline ==== | ||
| - | ===== Headline ===== | ||
| - | === See Also === | ||
| <WRAP noprint> | <WRAP noprint> | ||
| {{tag>Cubieboard Cubietruck}} | {{tag>Cubieboard Cubietruck}} | ||
| </WRAP> | </WRAP> | ||
tutorials/arduino/controlling_led.1393317454.txt.gz · Last modified: 2014/02/25 16:37 by sam
Page Tools
