CubieBoard Docs

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Begining On Lubuntu ======

<WRAP noprint><WRAP left box 60%>
//__About this Article__//
  * **Author**: allen --- allen@cubietech.com --- 2013/10/16 23:56
  * **Copyrights**: [[http://creativecommons.org/licenses/by-sa/3.0/|CC Attribution-Share Alike 3.0 Unported]]
  * **Contributors**: [[http://cubieboard.org/|Cubieboard Community]] : ...
</WRAP></WRAP>

===== Abstract =====

Here is a guide for people who are new to using lubuntu desktop/server on cubieboard. This article will cover the following，
  * Simple configuration
  * Setting up the development environment on board
  * Testing basic hardware
  * Troubleshooting



===== Configuration =====

==== SSH Connecting ====

Make sure cubieboard  can get to the Internet. If dhcp had been timeout, type:
<code bash>
  $dhclient eth0
</code>

Install openssh-service  in computer and cubieboard.
<code bash>
  $sudo apt-get install openssh-server 
</code>

''ssh username@IP''  in the terminal, press the password.

==== Set Time Zone/DateTime ====
1.Set time zone
<code bash>
  $sudo tzselect
</code>

Select the Asia , press Enter and chose China ,at last selet Beijing.

2. Cope file to /etc directory
<code bash>
  $sudo cp /usr/share/zoneinfo/Asia/Shanghai /etc/localtime
</code>

3. Update time
<code bash>
  $sudo ntpdate time.windows.com
</code>

==== Set keyboard language ====

Refer to [[tutorials:common:set_keyboard_language|Set Keyboard Language]]

==== Flashplayer ====
Download the [[http://dl.cubieboard.org/media/flashplayerarm.tar.gz|flashplayerarm]],type:
  $tar zxvf flashplayerarm.tar.gz  
  $sudo cp libpepflashplayer.so /usr/lib/chromium-browser/plugins
  $sudo cp default /etc/chromium-browser

==== Wifi ====

**CB1 and CB2 do not integraed wifi chip on board ,but we can use USB WIFI. **Make sure the wifi driver you use have been loaded. If not ,use
<code bash>

  $insmod /lib/modules/$(uname -r)/kernel/drivers/net/wireless/XXX.ko

</code>

**CB3(cubietruck) has integrated wifi chip .**

Type : ''modprobe bcmdhd'' to load the driver .

Add "bcmdhd" at the end of file  /etc/modules **to activate WiFi during boot**. For ecample with Lubuntu Desktop:
<code bash>  $sudo vi /etc/modules</code>

**Configure wifi at cubieboards and cubietruck the same way as descibed her:**
<code bash>
  $apt-get install linux-firmware
  $reboot
  $ifconfig wlan0 up   //open the wifi ,maybe wlan1 ..
  $iwlist wlan0 scan   //scan the wifi signal 
  $wpa_passphrase SSID passwd >> /etc/wpa_supplicant.conf  // the SSid is name of signal want to be used
  $vi /etc/network/interfaces
</code>
Add  below configuration  to /etc/network/interfaces 
<code bash>
  auto wlan0
  iface wlan0 inet dhcp   
  wpa-conf /etc/wpa_supplicant.conf
</code>
Add  below configuration  to /etc/resolv.conf
<code bash>
  nameserver 8.8.8.8
</code>
Reboot the cubieboard,auto gain the IP.
==== Setting CPU Frequency ====
Cubieboard CPU frequency can be adjusted in real time, , the following file save as shell file, or placed in / etc / rc.local before the exit 0 can be executed. Specific CPU frequency maximum and minimum values can be set based on usage .

<code bash>
  #!/bin/sh
  echo ondemand > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
  echo 1000000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
  echo 600000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_min_freq
  echo 25 > /sys/devices/system/cpu/cpufreq/ondemand/up_threshold
  echo 10 > /sys/devices/system/cpu/cpufreq/ondemand/sampling_down_factor



</code>
After testing, Cubieboard single core version (A10) CPU frequency can be overclocked to 1.2GHz, stable operation (would be better to stick a CPU heatsink); Cubieboard dual-core version (A20) can also be overclocked to 1.2GHz

==== Screenshots  Tool ====
<code bash>
  apt-get install shutter 
</code>
Type "shutter" in terminal to use ,like
{{:tutorials:common:shutter.png?700|shutter GUI}}


===== Developing =====

==== Using serial debug port ====

The tutorial how to use TTL cable: http://linux-sunxi.org/Cubieboard/TTL

Install the tool name minicom in your computer:
<code bash>
  $sudo apt-get install minicom
</code>
Set the minicom configuratiaon, TTL and cubieboard are connected ,then ''minicom''in the terminal ,enter into the console.

==== Installing target Toolchains ====

<code bash>
  $sudo apt-get update
  $sudo apt-get upgrade
  $sudo apt-get install vim build-essential git libusb-1.0-0-dev pkg-config -y 
</code>

===== Hardware Testing =====
**The best way to test hardware is install the office firmware from http://dl.cubieboard.org and usr office fitting from http://docs.cubieboard.org/addons，which can find the problem quickly you met.
Of course ,you should save the data before reinstall firmware.** 
==== LEDs On Cubieboaed ===
These are blue LED1 meaning heartbeat and green LED2 on cb1 and cb2. LED1 - GPIO port PH21, LED2 - GPIO port PH20. \\
These are LED1~4 on cb3(cubietruck). LED1 - PH21, LED2 - PH20,LED3 - PH11,LED4  - PH07.Refer to  [[ http://docs.cubieboard.org/faq/faqs|FAQ about cubietruck ]]\\
**For cb1 and cb2:**
<code bash>

  $echo 1 > /sys/class/gpio/export   //open the PH20 
  $echo 2 > /sys/class/gpio/export   //open the PH21
</code>
The directories /sys/class/gpio/gpio1_PH20 and/sys/class/gpio/gpio2_PH21 had been create . 
<code bash>
  $cd /sys/class/gpio /gpio1_PH20
  $echo out > direction    //set PH20 as output
  $echo 1 > value          //set PH20 as high ,grenn LED is light
  $echo 0 > value          //set PH20 as low,turn off the LED
</code>

==== HDMI ====
It would be best way connect the HDMI cable before power on the cubieboard,becuse some cable maybe appear the promble of sequence in time.\\
If your have not full screen display, you can try the following commands

  $fbset -left 10


1.If you are using lubuntu, try the following commands

  $wget http://dl.cubieboard.org/software/tools/armhf/cb-display-tool
  $chmod 777 cb-display-tool
  $cb-display-tool -o 8 -m 11  //switch to VGA type
  $cb-display-tool -o 4 -m 4  //switch to HDMI type

If you switch to other resolution, you need to restart your X after the modification

2.The default display configuration in script.bin of uboot partition of official desktop-firmware as :
<code>
;disp init configuration
;
;disp_mode            (0:screen0<screen0,fb0> 1:screen1<screen1,fb0> 2:two_diff_screen_diff_contents<screen0,screen1,fb0,fb1>
;                      3:two_same_screen_diff_contets<screen0,screen1,fb0> 4:two_diff_screen_same_contents<screen0,screen1,fb0>)
;screenx_output_type  (0:none; 1:lcd; 2:tv; 3:hdmi; 4:vga)
;screenx_output_mode  (used for tv/hdmi output, 0:480i 1:576i 2:480p 3:576p 4:720p50 5:720p60 6:1080i50 7:1080i60 8:1080p24 9:1080p50 10:1080p60 11:pal 14:ntsc)
;screenx_output_mode  (used for vga output, 0:1680*1050 1:1440*900 2:1360*768 3:1280*1024 4:1024*768 5:800*600 6:640*480 10:1920*1080 11:1280*720)
;fbx format           (4:RGB655 5:RGB565 6:RGB556 7:ARGB1555 8:RGBA5551 9:RGB888 10:ARGB8888 12:ARGB4444)
;fbx pixel sequence   (0:ARGB 1:BGRA 2:ABGR 3:RGBA) --- 0 for linux, 2 for android
;lcd0_bright          (lcd0 init bright,the range:[0,256],default:197
;lcd1_bright          (lcd1 init bright,the range:[0,256],default:197


[disp_init]
disp_init_enable = 1
disp_mode = 0
screen0_output_type = 3
screen0_output_mode = 4
screen1_output_type = 0
screen1_output_mode = 4
fb0_width = 1024
fb0_height = 768
fb0_framebuffer_num = 2
fb0_format = 10
fb0_pixel_sequence = 0
fb0_scaler_mode_enable = 0
fb1_width = 1024
fb1_height = 768
fb1_framebuffer_num = 2
fb1_format = 10
fb1_pixel_sequence = 0
fb1_scaler_mode_enable = 0
</code>

Modify the parameter according to the using HDMI displayer .For example ,''screen0_output_type = 3''set up HDMI output ,''screen0_output_type = 4''set up VGA output
You can get more information about  display  from [[http://linux-sunxi.org/Display |Display]] and modify script.bin from [[http://docs.cubieboard.org/tutorials/common/edit_the_system_configuration |edit_the_system_configuration ]]  
==== VGA ====
Refer to HDMI section.
Cubieboard1 and Cubieboard2 have no the VGA connector，but you can use [[http://docs.cubieboard.org/addons#cubie_breadboard|Cubie Breadboard]] to effect output.

==== USB Host====
The quickly way to test the interface of USB is plug the U disk . The system will identify the U disk .Use ''fdisk -l'' can see its information which meaning the interface of USB is working.  

==== IR ====
IR had beed add into the kernel .If not, use command to load the moudle:
<code bash>
  $insmod /lib/modules/$(uname -r)/kernel/drivers/input/keyboard/sunxi-ir.ko
</code>
<code bash>
  $sudo cat /dev/input/event0 | hexdump //or event1,event2
</code> 
Press the key of IR remote control,the terminal will print the message as:
<code bash>
0000000 8415 525f 50cf 0003 0001 0094 0001 0000                                 
0000010 8415 525f 50db 0003 0000 0000 0000 0000                                 
0000020 8415 525f 22f7 0007 0001 0094 0000 0000                                 
0000030 8415 525f 22ff 0007 0000 0000 0000 0000

</code>
The digital '0094' is  keycode of the remote control  .

The sunxi-3.4 IR is exposed as a a keyboard on the Linux input device interface. For example, the following simple keybinder application might be used to run arbitrary commands when receiving a specific keycode via IR. You can install it by
<code>
$ git clone https://bitbucket.org/emiliolopez/keybinder.git
$ cd keybinder
$ sudo make install
</code>
Configuration is handled on /etc/keybinder.conf, as a "keycode,command" pair per line. The application prints every keycode received, so you may as well use it to figure out the keycodes you want to use.

To execute the application, run
<code>
$ sudo keybinder /dev/input/event0
</code>
==== Headphone Jack ====
There are two audio devices HDMI and headphone in the cubieboard.
<code bash>
  $sudo  alsamixer
</code>
There are two audio devices named sunxi-sndhdmi and sunxi-CODEC in the system.
The sound output is send out from HDMI by default . You can adjust volume and other configuration ,use Ctrl + z to save it.\\
{{:tutorials:alsamixer.png?700|alsamixer GUI}}




To set sound care being sunxi-CODEC modify ''/etc/asound.conf'' to turn on the headphone.
<code bash>
  pcm.!default {
    type hw
    card 0    //If you want to set HDMI as output ,turn 0 to 1.
    device 0   
  }
  ctl.!default {
    type hw
    card 0   //If you want to set HDMI as output ,turn 0 to 1.
  }
</code>
If plug in the headphone and type:
<code bash>
  $speaker-test -twav -c2
</code>
The sound "sound left，sound right，sound left" will output from headphone.

Let cubieboard speak by package named espeak   : 
<code bash>       
  $sudo apt-get install espeak
  $espeak "hello"　　           //say: hello
  $espeak "hello_cubieboard"　　//say: hello cubieboard
</code>                                       
==== USB Camera ====
Most of the USB camera driver has integrated in the kernel，so it is  available insert camera into the cubieboard.
  $sudo apt-get install luvcview
  $luvcview -s 1080x720 (can modify the resolution)
  

If cubieboard has installed mplayer ,use mplyaer to display
<code>

  $mplayer tv://

</code>
==== Micro SD ====
TBD
==== SATA ====
TBD
==== OTG ====
The OTG cable is mini usb cable ,which used to flash firmware into nand .The guid to flash to board:
  - Press FEL key, and holding it
  - Plug in mini usb cable, and wait the following prombt
  - Release FEL key
After used some inferior cable to install firmware, the board maybe appear unknow system error.Powering on the cubiebaord via the cable ,which is unstable. Maybe the system will die or reboot some time ,so the recommended configuration is a 5V 2A power supply.


=====Troubleshooting=====
  * "No space left on device " while using apt-get install command.
  $sudo resize2fs /dev/nandd  (replace /dev/nandd to your real block device)


    

<WRAP noprint>
{{tag>Cubieboard Cubietruck}}
</WRAP>
CubieBoard Docs

User Tools

Site Tools

Page Tools
