CubieBoard Docs

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Start ======


<WRAP noprint><WRAP left box 60%>
//__About this Article__//
  * **Author**: aaron --- aaron@cubietech.com --- 2014/10/10 11:22
  * **Contributors**: [[http://cubieboard.org/|Cubieboard Community]] : ...
</WRAP></WRAP>

===== Abstract =====

{{:products:a20-cubietruck.png?600|}}

 
===== Hardware =====

==== Hardware Specs ====

  - AllWinnerTech SOC A20 ARM® Cortex™-A7 Dual-Core ARM® Mali400 MP2 Complies with OpenGL ES 2.0/1.1
  - 1GB/2GB DDR3@480MHz
  - HDMI&VGA 1080P display output on-board
  - 10M/100M/1G Ethernet
  - Wifi+BT wireless connection with antenna on-board
  - SATA 2.0 interface support 2.5’ HDD (for 3.5’ HDD, only need another 12V power input)
  - Storage solution NAND+MicroSD or TSD+ MicroSD or 2*MicroSD
  - 2 x USB HOST 1 x OTG 1 x SPDIF 1 x IR 4 x LEDs 1 Headphone 3 x Keys
  - Power DC5V @ 2.5A with HDD support Li-battery & RTC
  - 54 extended pins including I2S, I2C, SPI, CVBS, LRADC x2,UART, PS2, PWMx2, TS/CSI, IRDA, LINEIN&FMIN, TVINx4 with 2.0 pitch connectors
  - PCB size 11cm *8cm*1.4mm very suitable for installing a 2.5’ HDD 
==== Expansion Ports ====

{{:products:a20_cubietruck:ct-pin脚图.png?600|}}



^              **CN8 (Near Ethernet connector)**                   ^^^^
^                     **2x15 Header**                              ^^^^
|30|LRADC1                    |29|VCC-5V                              |
|28|LRADC0                    |27|CVBS                                |                            
|26|LINEIN-R                  |25|PB19(TWI1-SDA)                      |     
|24|LINEIN-L                  |23|PB18(TWI1-SCK)                      |
|22|PB4 (IR0-RX)              |21|PB2 (PWM0)                          |
|20|PB3 (IR0-TX))             |19|PI3 (PWM1)                          |
|18|PI15 (PS2SDA1/EINT27)     |17|PI21 (FMIN-R/PS2SDA0/UART7-RX/HSDA) |
|16|PI14 (PS2SCLK1/EINT26)    |15|PI20 (FMIN-L/PS2SCLK0/UART7-TX/HSCL)|
|14|GND                       |13|GND                                 |
|12|PB17 (SPI2-MISO/JTAG_DI0) |11|PB15(SPI2-CLK/JTAG_CK0)             |
|10|PB16 (SPI2-MOSI/JTAG_DO0) |9|PB14 (SPI2-CS0/JTAG_MS0)             |
|8|PC22 (SPI2-MISO/EINT15)    |7|PC20 (SPI2-CLK)               |
|6|PC21 (SPI2-MOSI/EINT14)    |5|PC19 (SPI2-CS0)               |
|4|RESET#                     |3|AVCC                                 |
|2|3.3V                       |1|GND                                  |




^                **CN9 (Near USB Ports)**                                 ^^^^
^                   **CSI1/TS/TP/TVIN**                                   ^^^^
|1|3.3V                           |2|3.3V                                    |
|3|PG0 (TS1_CLK/CSI1-PCLK)        |4|PG3 (TS1_ERR/CSI1-VSYNC)                |
|5|PG2 (TS1_SYNC/CSI1-HSYNC)      |6|PG1 (TS1_DVLD/CSI1-MCLK)                |    
|7|PG4 (TS1_D0/CSI1-D0)           |8|PG5 (TS1_D1/CSI1-D1)                    |
|9|PG6 (TS1_D2/CSI1-D2/UART3-TX)  |10|PG7 (TS1_D3/CSI1-D3/UART3-RX)          |
|11|PG8 (TS1_D4/CSI1-D4/UART3-RTS)|12|PG9 (TS1_D5/CSI1-D5/UART3-CTS)         |
|13|PG10 (TS1_D6/CSI1-D6/UART4-TX)|14|PG11 (TS1_D7/CSI1-D7/UART4-RX)         |
|15|GND                           |16|GND                                    |
^                             **Analog**                                  ^^^^
|17|XP-I2SDO1                     |18|TVIN0-I2SMCLK                          |
|19|XN-I2SDO2                     |20|TVIN1-BTPCMCLK                         |
|21|YP-I2SDO3                     |22|TVIN2-BTPCMSYNC                        |
|23|XN-BTPCMIN                    |24|TVIN3-BTPCMOUT                         |



===== Software =====

==== Abstract ====


===== Installation =====

==== Android ====
  * [[tutorials:ct1:installation:CB3 A20-Compiling Android image for Cubietruck | A20-Compiling Android image for Cubietruck]]
  * [[tutorials:ct1:installation:CB3 A20-Install Nand Boot Android for Cubietruck | A20-Install Nand Boot Android for Cubietruck]]
  * [[tutorials:ct1:installation:CB3 A20-Android Boot from SATA | A20-Android System Boot from SATA]]
  * [[tutorials:ct1:installation:A20 A20-Add custom plan board android configuration | A20-Add custom plan board android configuration]]

==== Cubieez ====

  * [[tutorials:CubieTruck:cubieez | Get start with Cubieez ]]
 

==== Lubuntu ====
  * [[tutorials:ct1:installation:CB3 Lubuntu-12.10-Desktop Nand Installation(20130910-build)|Lubuntu-12.10-Desktop Nand Installation Guide(20131015-build)(old)]]
  * [[tutorials:ct1:installation:CB3 Lubuntu-12.10-Desktop Nand Installation(v1.00)|Lubuntu-12.10-Desktop Nand Installation Guide(v1.00)]]
  * [[tutorials:ct1:installation:Install Lubuntu Desktop_or_Server Rootfs to SATA drive|Install Lubuntu Desktop/Server Rootfs to SATA drive(obsolete)]]
  * [[tutorials:ct1:installation:Moving rootfs from nandflash to hard drive|Moving Rootfs From Nandflash to Hard Drive]]
  * [[tutorials:ct1:installation: install_lubuntu_desktop_server_to_sd_card | Install lubuntu desktop/server to SD card ]]
   

==== Fedora ====
  * [[tutorials:ct1:installation:CB3 Fedora19(r3) SD Card Installation|Fedora19(r3) SD Card Installation Guide]]

===== Development =====
  * [[tutorials:ct1:development:Compiling Latest Kernel for cubietruck(cubieboard3)|Compiling Latest Kernel for cubietruck(cubieboard3)]]
  * [[tutorials:ct1:development:Booting from USB OTG Port|Booting from USB OTG Port(For recovery)]]
  * [[tutorials:ct1:development:Bulid a Java development environment for cubietruck|Bulid a Java development environment for cubietruck]]
  * [[tutorials:ct1:development:How to use rdesktop to display windows or linux desktop|How to use rdesktop to display windows or linux desktop]]
  * [[tutorials:ct1:development:Booting the Cubietruck over the network|Booting the Cubietruck over the network]]
 
<WRAP noprint>
{{tag>Cubieboard Cubietruck}}
</WRAP>
CubieBoard Docs

User Tools

Site Tools

Page Tools
