This shows you the differences between two versions of the page.
addons [2013/10/23 15:03] james [Cubie Breadboard] |
addons [2013/12/23 14:50] (current) |
||
---|---|---|---|
Line 6: | Line 6: | ||
- Add 2.54mm pitch 96 pins male-connector, for ease of breakout all the extended funcions pins in this baseboard | - Add 2.54mm pitch 96 pins male-connector, for ease of breakout all the extended funcions pins in this baseboard | ||
- Offering 1312 isolated cell-vias with size of 1.1mm/1.8mm and 2.54mm pitch, for ease of doing circuitry DIY experiment | - Offering 1312 isolated cell-vias with size of 1.1mm/1.8mm and 2.54mm pitch, for ease of doing circuitry DIY experiment | ||
- | {{:addons:selection_061.png|}} | + | {{:addons:selection_061.png?400|}} |
===== MicroSD Breakout ===== | ===== MicroSD Breakout ===== | ||
For exporting UART and JTAG pins of Cubieboard | For exporting UART and JTAG pins of Cubieboard | ||
- | {{addons:usd2.jpg|uSD breakout?200px}} | + | {{addons:usd2.jpg?400}} |
===== Cubie Black & White Acrylic Case ==== | ===== Cubie Black & White Acrylic Case ==== | ||
Line 17: | Line 17: | ||
(2) Convenient to access SATA and 96 extended pins even with this case. | (2) Convenient to access SATA and 96 extended pins even with this case. | ||
- | {{addons:y.png|black & white case?200px}} | + | {{addons:y.png?400}} |
===== Cubie Simple Acrylic Case ===== | ===== Cubie Simple Acrylic Case ===== | ||
Suitable for developers, convenient to access all the interfaces of cubieboard. | Suitable for developers, convenient to access all the interfaces of cubieboard. | ||
- | {{addons:img_1239.jpg|case1?200px}} | + | {{addons:img_1239.jpg?400}} |
===== Transparent Case for Cubieboard===== | ===== Transparent Case for Cubieboard===== | ||
The same with Black&White Case, but the color is different | The same with Black&White Case, but the color is different | ||
- | {{addons:img_1228.jpg|case2?200px}} | + | {{addons:img_1228.jpg?400}} |
===== TTL to USB serial cable ===== | ===== TTL to USB serial cable ===== | ||
+ | {{:addons:selection_062.png?400|}} | ||
+ | =====2 in 1 heatsink package===== | ||
+ | -Clean up the surface of the main chip, make sure not to have greasy dirt | ||
+ | -Coat with a thin layer of thermal silicone on the surface,recommended thickness is 0.1~0.5mm,the thinner the better | ||
+ | -Attach the metal block, press slightly, adjust the position of the main chip, do not move within 10 minutes. Warning: This silicone adhesive force is large, not easy to remove after dry | ||
+ | {{:addons:selection_063.png?400|}} | ||
+ | =====All in one heatsink===== | ||
+ | The usage of All in one heatsink is more easy. Just rip off the gummed paper and then stick it on the | ||
+ | mainchip. | ||
+ | {{:addons:selection_064.png?400|}} | ||
+ | =====12V-5V SUB===== | ||
+ | -The function of 12V-5V SUB is to support 3.5-inch hard disk drive in Cubieboard or Cubietruck. And you can also use it if you haven’t a 2A@5V adapter but a 12V adapter. It is very useful if you have an old HDD and want to build a personal entertainment media center. | ||
+ | -This is a simple board which made by a newbie from Cubietech, we offer all the design files. | ||
+ | {{:addons:selection_065.png?400}} | ||
<WRAP noprint> | <WRAP noprint> | ||
{{tag>Cubieboard Cubietruck}} | {{tag>Cubieboard Cubietruck}} | ||
</WRAP> | </WRAP> |